Jump to content

Recommended Posts

I'm using the FUJINON LENS XF50-140mmF2.8 R LM OIS WR on a XT-3. Have both for a few months and been very happy, until a few days ago.  After I switch the camera on, I get this wizz sound on the lense that doesn't stop. It wasn't always like that, so I wonder whether there's a problem with the lense, or whether I accidentally changed a camera setting that triggers this. My apologies in advance if this is an inappropriate or otherwise stupid question. I'm trying to avoid having to trek back to the dealership (different city etc etc), unless there's genuine cause for concern. Any comments would be much appreciated.

Edited by udo
Link to post
Share on other sites

  • 2 weeks later...

That lens, by the way, always has a very soft electronic sound, even when "IS"  turned off.

I can only hear it in a quiet room when I put it to my ears.

I believe that's something about "floating glass elements" that are engaged when powered on. You can hear the elements clunk about inside when the lens is powered off ( that's also normal).

But, you indicated it's a much louder sound and you just noticed, it so I'm guessing it's "PRE-AF ON"...

If it's simply the soft noise of the lens then that is normal.

Link to post
Share on other sites

Pete1959,

I also hear a whirring noise from my 18-135 and 18-55 Fujinon lenses with my ear up close in a quiet room. The sound disappears when the camera sleeps or is powered off. It sounds like a tiny motor.

  • I have Pre-AF off
  • I have OIS off.
  • I am in "S" on the M-C-S focus switch

I've had this camera for 2 years and started noticing a more rapid battery drain. I wondered if something is not set right or working right.    You mentioned some other ideas earlier in this forum.

 

Thanks

 

Stan

Edited by Snsokstan
typo
Link to post
Share on other sites

  • 2 weeks later...
On ‎4‎/‎7‎/‎2019 at 12:41 PM, Snsokstan said:

Pete1959,

I also hear a whirring noise from my 18-135 and 18-55 Fujinon lenses with my ear up close in a quiet room. The sound disappears when the camera sleeps or is powered off. It sounds like a tiny motor.

  • I have Pre-AF off
  • I have OIS off.
  • I am in "S" on the M-C-S focus switch

I've had this camera for 2 years and started noticing a more rapid battery drain. I wondered if something is not set right or working right.    You mentioned some other ideas earlier in this forum.

 

Thanks

 

Stan

Hi Stan:

RE: Batteries:

"Face Detect">On , if left "ON", will also continuously hunt for faces even when not half pressing and will drain battery faster. Only have it on when you need it.

Blue Tooth>Turn it off. It is by default set to "On"

Boost> Not needed for landscape and slow non action shooting. Turn it off if not needed.

Occasionally fully discharge the batteries to maintain lithium battery health.

-Peter

 

PS: Two years...? The camera came out in late Sept. 2019.....are you speaking of the XT2 ? The XT3 gets noticeably better battery life...

 

Link to post
Share on other sites

  • 2 years later...

Occasionally fully discharge the batteries to maintain lithium battery health.

A full discharge is apparently not good for lithium batteries.  Every time that happens, battery life is degraded.

(Extra tip, the best long term storage life is at 50% charge.)

Link to post
Share on other sites

  • 4 weeks later...

I think that you are describing the normal noise from this lens and others. It's the gyros for the IOS, which run all the time irrespective of whether IOS is on or off. Also there may be some noise from the linear motors that do the focusing. I am not sure about the latter. The noise is normally very low so either you have sensitive hearing or perhaps there could be sometimes  wrong but I doubt it.

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

  • Posts

    • Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
    • Typically you need to make sure the lens is compatible with the camera, i.e. check the lens compatibility charts for your camera, then make sure the respective firmwares are updated so older issues are resolved. After that, each lens has a manufacturer’s profile which will be embedded into the raw file meta data for the images captured using that lens. From there, it is up to the raw conversion software  to apply the lens correction to the image. Different converters do that differently, some automatically, some only if a setting is turned on. For in-camera jpegs, the on-board converter does the corrections automatically, assuming the camera recognizes the lens, it applies a generic profile otherwise. I do not know if that can be turned off or not.
    • How does one make sure that Fuji's image correction is turned on to correct barrel and pin-cushion distortion on a GFX 100 or GFX100S when using the GF20-35? Is it only applied to the jpegs and not to the raw files? (I was surprised to discover the barrel distortion on the GF 35-70mm lens.) I normally shoot in raw with jpeg back-up and use the raw files, which I convert either in Affinity Photo 2 when editing with that program or in Raw File Converter Ex 3.0 by Silkypix if I wish to process the image in Photoshop CS6. (Adobe DNG is also a possibility.) Thank you for the help. Trevor
    • Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

    • Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

×
×
  • Create New...