Jump to content

Fuji X100F exposure way off

muisephoto
 Share

Recommended Posts

muisephoto Newbie

muisephoto

Posted
Posted

I recently purchased a new Fuji X100F.  It seemed to be working fine with no exposure issues up until one month ago.  When I hold up the camera to shoot, the LCD shows a scene perfectly exposed.  When I press the shutter down halfway the LCD is sometimes 1-3 stops either underexposed or overexposed, not even close.  I have had to use exposure compensation in order to get a properly exposed picture.  I know the camera very well and have read the manual several times to look for a clue as to a setting that may be out of whack.  I have tried all the different exposure modes.  I know these cameras have had exposure issues in the past.  Any ideas?  I tried resetting all the settings.  Should I look for a factory firmware update?

Thanks!!!

Matt

Link to post
Share on other sites
dfaye Enthusiast

dfaye

Posted
Posted (edited)

It sounds like the sticky aperture blade problem that affected some of the earlier X100 models. There are several YouTube videos, for example 

 

and also other discussion online, if you Google "Fuji X100 sticky aperture blade problem". If this is the answer, your camera would have to go back to Fuji for repair (but I think it's a fairly simple repair). Good luck!

Edited by dfaye
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Content

  • Posts

    • thelostkiwi
      Looking for Full Frame lenses to adapt to GFX

      By thelostkiwi · Posted

      I also use a Nikon to GFX Fringer and it works very well.  24mm f/1.8 vignettes so best used on 35mm mode.  50mm f/1.8 covers the entire frame very well with no issues and is a superb little lens. 105mm Sigma vignettes slightly but is perfectly usable. 300 f/4 likewise the 105.  I have a 70-200 f/20+.8 incoming to test so will report back but I'm expecting a little vignetting.  Even in 35mm mode the image is still 60MP and if you're prepared to manually crop and correct you can get 80-90 MP images.  I also have a C/Y to GFX adapter.  The 24mm Sigma Superwide vignettes strongly. Ditto 28-80 Zeiss Sonnar. 80-200 f/4 Sonnar is perfectly usable. All work fine as 35mm mode lenses.  I also have an M42 adapter which I tried with the Carl Zeiss Jena 135mm f/3.5 with good results. 
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Thank you. I will research it.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Typically you need to make sure the lens is compatible with the camera, i.e. check the lens compatibility charts for your camera, then make sure the respective firmwares are updated so older issues are resolved. After that, each lens has a manufacturer’s profile which will be embedded into the raw file meta data for the images captured using that lens. From there, it is up to the raw conversion software to apply the lens correction to the image. Different converters do that differently, some automatically, some only if a setting is turned on. For in-camera jpegs, the on-board converter does the corrections automatically, assuming the camera recognizes the lens, it applies a generic profile otherwise. I do not know if that can be turned off or not.
×
×
  • Create New...