Jump to content

Recommended Posts

I'm wondering if anyone has experienced something similar to what I experienced recently.  

I recently picked up the X-T3 along with the 50-140 lens (replaced my full frame Nikon gear).

To put it into context, I shoot my kids hockey games.  I noticed when tracking players on the ice, there was a periodic pause in the image in the EVF.  

Wondering if it is a setting issue on my end or if it was the norm?  The issue is if the image lags, I may miss a shot.  I'm using the same setting I use to use with my old gear - continuous AF, auto ISO (3200 max) and aperture at 2.8.  Shutter priority at 800.  

Face detection is off and have set the AF-E button as my back AF button.

 

Thoughts?

Link to post
Share on other sites

Are you using the latest firmware? Might be the back button focusing.

Your issue might be related to some issues i found on the latest firmware:
-Using back button focus the following happens:
.in af-c wide/tracking, the camera starts tracking another thing after a single shot, or at the end of a burst;
.in af-c wide/tracking, with face/eye detect, sometimes the viewfinder lags on the end of a burst.

Possibly this also happens using zone focus, haven´t tested.

Also, when using any of the zone areas, with auto or center zone area switching, the camera has a tendency to never focus on the center point.

Link to post
Share on other sites

Thanks.  I did update to the latest firmware and only use single point focus.

It may not be a AF tracking issue.  Maybe it's just a EVF vs. the normal glass viewfinder on my old Nikon which is something I'm just going to have to get use to.

I essentially watch the game following the puck using the viewfinder and won't focus unless I think a good shot is coming.  So the lag I'm experiencing is when I'm just panning the camera following the plays.

 

Link to post
Share on other sites

If "during shooting" the card may have a problem....bad cards are frequently the culprit in rare weird freezes and lockups when the camera has issues writing to the card.

So...swap cards...format cards...try a new card...etc.

Good luck...please post solution if you figure it out (even if it's user error) :-)

-P

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

  • Posts

    • I use a TECHART ring to mount Canon EF lenses on the GFX 50S-II and 100S-II, maintaining image stabilization and autofocus. The only limitation are lenses with a small rear element diameter that make it impossible to cover medium format. Fast lenses like the EF 85/1.2L or the 100-400L, however, work great.
    • I also use a Nikon to GFX Fringer and it works very well.  24mm f/1.8 vignettes so best used on 35mm mode.  50mm f/1.8 covers the entire frame very well with no issues and is a superb little lens. 105mm Sigma vignettes slightly but is perfectly usable. 300 f/4 likewise the 105.  I have a 70-200 f/20+.8 incoming to test so will report back but I'm expecting a little vignetting.  Even in 35mm mode the image is still 60MP and if you're prepared to manually crop and correct you can get 80-90 MP images.  I also have a C/Y to GFX adapter.  The 24mm Sigma Superwide vignettes strongly. Ditto 28-80 Zeiss Sonnar. 80-200 f/4 Sonnar is perfectly usable. All work fine as 35mm mode lenses.  I also have an M42 adapter which I tried with the Carl Zeiss Jena 135mm f/3.5 with good results. 
    • Thank you. I will research it.
    • Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
×
×
  • Create New...