Jump to content

XF 70-300mm, quite often declines to AF, even in bright conditions


Recommended Posts

I experienced quite often the refuse of the XF 70-300mm to focus on AF on X-S10. This happens in various light conditions, the first time was in bright conditions. I am wondering this happens on other bodies too, or is the fault of the lens itself,  that needs a new firmware?

Edited by Gion
Link to post
Share on other sites

  • Gion changed the title to XF 70-300mm, quite often declines to AF, even in bright conditions
  • 1 month later...
  • 10 months later...

Hi, was this problem solved in a FW update? Today I tested out a second hand X-S10 with my own XF 70-300 (+TC 1.4). This lens works fine on my own X-T30, but was out of focus on the X-S10. Camera was set to M, it did focus most of the time on A but quite often, especially when moving from a nearby object to an object in the far distance and full zoom it didn’t manage to focus but did show a green rectangle. The focus was not a bit off, it almost seemed it stayed at the previous state. Sometimes, after switching back from “A” to “M”, it worked for a few shots but then it refused to focus again. On my own camera there is never a problem.

I must say that the tested camera’s FW was still on 1.1, wasn’t able to update the FW to the latest during the test.

So I would like to know if this was solved for the original poster of this topic in later updates? Fuji remains very vague about certain bugs and I didn’t see any notice in the later FW notes about the combination of this lens and body.

Link to post
Share on other sites

14 hours ago, cpX said:

That sounds to me like the AF-On button is active.

We did a full reset of the camera and also the lens didn’t focus sometimes, so I think this can’t be the problem. It did focus a few times after going from “A” to “M” mode, put the longer we tried in “M” the more problematic it became.

Link to post
Share on other sites

  • 1 year later...
  • 3 weeks later...
On 6/7/2022 at 12:45 AM, arachnida said:

We did a full reset of the camera and also the lens didn’t focus sometimes, so I think this can’t be the problem. It did focus a few times after going from “A” to “M” mode, put the longer we tried in “M” the more problematic it became.

You realize M is manual focus mode?  Also, the min focus distance has to be met or no focus.  I believe the min focus is longer with the 1.4 attached.

Link to post
Share on other sites

  • 4 weeks later...
On 2/21/2024 at 9:06 PM, Nicole D said:

I am also running into this problem. I am using the XT5 and increasingly having focusing problems with the 70-300 while all settings are checked, so this is not the problem. Has anyone found a solution to the problem?

I am also on the same setup. I noticed on the photos once i look on my laptop screen. But I noted that issue in continuous autofocus mode and it looks ok on single focus. 

Link to post
Share on other sites

  • 5 months later...

I'd had the 70-300 for about a year now.  

Unreliable focusing - especially at 300mm end. often focus behind subject is static and in center of frame.  Infuriating with birds for example!  You think you have a bang-on sequence of several shots and they often all turn out out out of focus.  I try shooting short bursts, then refocus and shot another burst - this has often saved me - but man this gets frustrating! :-(

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Posts

    • I also use a Nikon to GFX Fringer and it works very well.  24mm f/1.8 vignettes so best used on 35mm mode.  50mm f/1.8 covers the entire frame very well with no issues and is a superb little lens. 105mm Sigma vignettes slightly but is perfectly usable. 300 f/4 likewise the 105.  I have a 70-200 f/20+.8 incoming to test so will report back but I'm expecting a little vignetting.  Even in 35mm mode the image is still 60MP and if you're prepared to manually crop and correct you can get 80-90 MP images.  I also have a C/Y to GFX adapter.  The 24mm Sigma Superwide vignettes strongly. Ditto 28-80 Zeiss Sonnar. 80-200 f/4 Sonnar is perfectly usable. All work fine as 35mm mode lenses.  I also have an M42 adapter which I tried with the Carl Zeiss Jena 135mm f/3.5 with good results. 
    • Thank you. I will research it.
    • Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
    • Typically you need to make sure the lens is compatible with the camera, i.e. check the lens compatibility charts for your camera, then make sure the respective firmwares are updated so older issues are resolved. After that, each lens has a manufacturer’s profile which will be embedded into the raw file meta data for the images captured using that lens. From there, it is up to the raw conversion software to apply the lens correction to the image. Different converters do that differently, some automatically, some only if a setting is turned on. For in-camera jpegs, the on-board converter does the corrections automatically, assuming the camera recognizes the lens, it applies a generic profile otherwise. I do not know if that can be turned off or not.
×
×
  • Create New...