Jump to content

X-T2 card problem

Vasilis

By Vasilis
in Fuji X-T2 / Fuji X-T20

 Share

Recommended Posts

Vasilis Contributor

Vasilis

Posted
Posted (edited)

I had several times  the same card problem with the X-T2 : i use the Lexar 2000x 64gb on the first slot for RAW and 4K videos and a Lexar 1000x 64GB on the second one for jpegs .When the first card gets full ,the message 'memory card full' appears .I switch to the second slot ,which still has plenty of space,but the problem it's there. I change the 'save data setup', shoot only raw,i remove the full memory card ,i switch the empty to the 1st slot ,still i can't shot.The problem is being solved only if i carry a 3rd card and place it to the first slot. Is there any solution or a specific setup to avoid this situation?

Edited by Vasilis
Link to post
Share on other sites
jlmphotos Experienced

jlmphotos

Posted
Posted

If you have the save data setup set to overflow you shouldn't have to physically switch cards.  Once slot 1 is full, it'll start filling up the card in slot 2.

 

No need to do anything else.  Is this the problem?  I think we have a slight language barrier here.  Let us know.

Link to post
Share on other sites
jlmphotos Experienced

jlmphotos

Posted
Posted

The camera if set tot he way you have it, and you moved a card from slot 2 into slot 1, and didn't replace the card in slot 2, it will not shoot.  I experience the same issue.  However, if you pull the card out of slot 1, and leave the other card in slot 2, then the camera will continue to work.  I think this is a firmware problem. 

 

Again: I think we have a slight language barrier problem.  I hope this helped.

Link to post
Share on other sites
Vasilis Contributor

Vasilis

Posted
  • Author
Posted (edited)

I've done this as well ,still didn't work  .Which option to choose from Sequential-Backup-Raw?because i've tested all and still nothing . Your last solution bellow showed ' no card on slot 1' and couldn't shoot.

 

 However, if you pull the card out of slot 1, and leave the other card in slot 2, then the camera will continue to work.  I think this is a firmware problem. 

 

 

Edited by Vasilis
Link to post
Share on other sites
jlmphotos Experienced

jlmphotos

Posted
Posted

I've done this as well ,still didn't work  .Which option to choose from Sequential-Backup-Raw?because i've tested all and still nothing . Your last solution bellow showed ' no card on slot 1' and couldn't shoot.

 

I'm going to test this and get back to you

Link to post
Share on other sites
jlmphotos Experienced

jlmphotos

Posted
Posted

I tested my X-T2 this morning and here is what I found:

 

I had two cards in the camera.

In BACKUP MODE:

If I took the card in slot 2 out, the camera locks up.  

If I insert the card back in slot 2, then take out the card in slot 1, same error.  Which makes total sense.

 

In SEQUENTIAL MODE:

If i pull the card out slot 1, the camera still shoots.

If I put the card back in slot 1, and then pull the card out of slot 2, the camera still works.

 

In RAW/JPEG MODE:

If I pull the card out of either slot, the camera won't shoot.

 

Hope that helps.

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Content

  • Posts

    • thelostkiwi
      Looking for Full Frame lenses to adapt to GFX

      By thelostkiwi · Posted

      I also use a Nikon to GFX Fringer and it works very well.  24mm f/1.8 vignettes so best used on 35mm mode.  50mm f/1.8 covers the entire frame very well with no issues and is a superb little lens. 105mm Sigma vignettes slightly but is perfectly usable. 300 f/4 likewise the 105.  I have a 70-200 f/20+.8 incoming to test so will report back but I'm expecting a little vignetting.  Even in 35mm mode the image is still 60MP and if you're prepared to manually crop and correct you can get 80-90 MP images.  I also have a C/Y to GFX adapter.  The 24mm Sigma Superwide vignettes strongly. Ditto 28-80 Zeiss Sonnar. 80-200 f/4 Sonnar is perfectly usable. All work fine as 35mm mode lenses.  I also have an M42 adapter which I tried with the Carl Zeiss Jena 135mm f/3.5 with good results. 
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Thank you. I will research it.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Typically you need to make sure the lens is compatible with the camera, i.e. check the lens compatibility charts for your camera, then make sure the respective firmwares are updated so older issues are resolved. After that, each lens has a manufacturer’s profile which will be embedded into the raw file meta data for the images captured using that lens. From there, it is up to the raw conversion software to apply the lens correction to the image. Different converters do that differently, some automatically, some only if a setting is turned on. For in-camera jpegs, the on-board converter does the corrections automatically, assuming the camera recognizes the lens, it applies a generic profile otherwise. I do not know if that can be turned off or not.
×
×
  • Create New...