Jump to content

Is it worth fixing a GFX 100s sensor?


Recommended Posts

I've got a sensor on a GFX100s that seems to have bad pixels / bright pixels that are not controlled by the pixel mapping in the firmware.  Pixel mapping improves the images temporarily but even after mapping does not completely remove bad pixels.  Although this problem became significantly stronger a couple of weeks after the one year warranty ended I can see them in low key shots at least sas early as six months after purchasing the camera. 

Other than I'm disappointed Fujifilm does not seem to consider this a defective sensor but an out of warranty situation with the cost on me.  I find it alarming that the most expensive body I've bought lasted for such a short time - especially after the research I did when I switched to Fujifilm suggested they had strong builds and quality control.  I would really appreciate comments on experiences with other GFX sensor problems becasue at this point I cannot justify spending that much money to fix something that has failed so quickly.  This is night and day difference in my experience with previous cameras and their manufacturers.

Thanks,  John

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

  • Posts

    • so if i'm shooting uncompressed 16-bit RAW files it takes a significant amount of time to write to card. Got the high end UHS II cards, and this does not happen with burst shooting, only single frame shots. what setting am i missing that causes this to happen?
    • The Tentacle Sync Timecode tool is the one I tried. I couldn't get it to work. But that is probably my fault, not the software. I seemed to get a file, but I couldn't turn it into anything meaningful. 
    • I am glad to read you are able to get this up and running. Pretty much as long as you connect the camera and turn it on and wait a few moments for the computer to register the connection, you can then use Image Capture (which actually is a very decent program with a lot of options for transferring images from cameras to the computer) or Lightroom or other programs to move the images to your library. There are some drawbacks; connecting to the computer while it is in sleep mode will waste your time, the connection will not get recognized— you will have to unplug the camera, wake the computer and start over. Trying to connect while the screen saver is running may work, it may not, often not. If the computer goes into screen saver mode while the camera is connected and sitting idle, it usually stays connected when coming back out of screen saver, but if the computer mputer goes into sleep mode, the connection gets dropped and you have to unplug it and start over. I suggested having the camera turned off while connecting, this is to lower the possibility of static electricity discharges frying either the camera or the computer or both. A lot of times you can connect while the camera is turned on, but not always, sometimes you have to unplug, turn it off, reconnect and turn it back on. A lot of this comes from Apple’s approaches towards keeping USB devices from hijacking your computer, some is just hubris and some is from the vagaries of chance. p.s. Your laptop should be able to connect to the camera.
    • Hi Chas, I am just fallen into the rabbit hole of investigating how to upgrade my X-T4's video sound... Loving the idea of time code sync, I am now quite concerned that the X-T4 doesn't support it, although I have already seen different statements on the net, like here:  https://youtu.be/xja27RmvbhE?si=hIch3Tu_MH_pWSBH&t=571 I have to admit, this guy's "explanation" gets quite confusing in his further discourse ...:) BUT, as you wrote that you use Tentacle Sync for Windows!, did you also try with their windows-only software "Time Code Tool" which you find here?: https://tentaclesync.com/timecode-tool   Would love to here if you found a workaround with the XT4 Best, Simon
    • It occurred sometime when I focus. It is not silent 
×
×
  • Create New...