Jump to content

Loose rubbergrip

Halin59

By Halin59
in General Discussion

 Share

Recommended Posts

Halin59 Newbie

Halin59

Posted
  • Author
Posted
8 minutes ago, Maxtoon said:

I sent my X-T1 to Phototech, It was expensive, about $150.00, but they were fast and the result was perfect. Totally replaced skin.

Photo Tech/Chrysler Camera Repair
575 Eight Avenue, Suite 1706
(Between 38th & 39th Street)
New York, NY 10018
212-673-8400 & 212-682-3547
www.phototech.com

Ok. Did you lift up the rubber a little and squeezed in some glue and then put some pressure on it? 

Link to post
Share on other sites
ChrisWebb Rookie

ChrisWebb

Posted
Posted
On 6/9/2023 at 5:35 PM, jlmphotos said:

I have used gorilla glue on my XT1 and it's held up for years now.

If anybody uses Gorilla glue remember that you need to dampen the surfaces with a very small amount of water first to activate the glue. For this purpose a small artist's brush might be best.

On 6/9/2023 at 5:35 PM, jlmphotos said:

 

 

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Posts

    • thelostkiwi
      X70 any active forums for this camera?

      By thelostkiwi · Posted

      I never knew the X70 existed! Looks interesting.
    • MYH
      Can't connect to XApp

      By MYH · Posted

      Equipment: Fujiflim X-M5 (firmware V 1.10). iPhone 15 pro (26.1) I am unable to properly connect my Fujifilm X-M5 to XApp on my iPhone 15 Pro. This setup previously worked without issues, but now the app only supports a basic remote shutter and no longer allows Get or Take mode, which are required for remote parameter control and shooting. I have repeatedly Initialized “FUJIFILM XApp”, re-paired the camera, reset wireless settings, and confirmed the camera is not in airplane mode, with both devices placed next to each other. None of these steps resolved the issue. Also, I am unable to update the camera firmware, as the process always fails with a “connection failed” message. I need clarification on whether this is a known firmware or compatibility issue and what the actual solution is.

      Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

    • jerryy
      Fall pictures

      By jerryy · Posted

      Last day of autumn 2025. Autumn is gradual. Summer field crops slowly ripening. Cool, longer nights turn into morning fogs. Color (colour) touches here and there taking the place of flowers now resting until Spring. Then, after that slow introduction, Fall is everywhere. Winter is brash, Winter is not at all subtle. Freezing cold days and colder nights. The Sun struggles to get above the horizon. Bare fields, iced over streams and woe (‘Woe!! I say!’) to trees or shrubs holding onto leaves.

      Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

        But there is sledding, skiing and hot chocolate for those that like those things 😀.
    • jerryy
      Fall pictures

      By jerryy · Posted

      Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

      Winter is coming.
    • Sailortim
      Exposure Compensation Dial vs Display

      By Sailortim · Posted

      For some reason, the EV dial setting does not correlate to the EV setting displayed in the viewfinder.  My XT2 used to have parity between settings such that when the dial was at "0", the viewfinder also showed "0".  Has anybody else noticed this?  I've tried a reset of the s/w but no luck.  
×
×
  • Create New...