Jump to content

Nissin i40 HSS on XT1 Help!

JohnDizzo15
 Share

Recommended Posts

JohnDizzo15 Rookie

JohnDizzo15

Posted
Posted

Just got my i40 in the mail from Amazon today. Specifically purchased it to use HSS but can't seem to figure out how to make it work after following the instructions on the hack.

 

I have placed the flash in manual mode and held down the test button for 3 seconds so that the light next to the M is blinking. Still, no HSS since it is still not lighting the scene completely when shooting higher than 1/200th.

 

I also have firmware 4.0 installed. Not sure if this has anything to do with it. Any help would be greatly appreciated as I am not able to find any other assistance on the net thus far.

Link to post
Share on other sites
Patrick FR Veteran

Patrick FR

Posted
Posted

Maybe this can help: http://www.fujirumors.com/fuji-nissin-i40-hss-force-trick-enable-sync-speeds-up-to-14000-on-your-x-series-camera/
 
Turn the i40 to manual mode Press and hold test button for three seconds
Watch the lamp next to the m for manual go on and off. You just turned on high speed sync!
Turn on flash put the right dial on the speed you need HSS works up to 1/4000

To activate the HSS you need do is turn the flash to manual, press and hold the test button for 3 seconds, which is the power LED. After 3 seconds the LED next to the manual control will flash. Unfortunately you are now not in TTL mode so it will only sync with the manual flash controls, but that is good enough.

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Content

  • Posts

    • Michaelb5
      ISO and exposure dial’s misbehaving. Need help

      By Michaelb5 · Posted

      Hey everyone, I am new to the fujifilm system, and I just received my X100vi about 15 days ago, and yesterday I noticed that ISO and exposure dials are acting up. I spent hours watching YouTube videos and reading forms without finding any solutions. Using ChatGPT or Gemini also didn’t help. My issues are the following: If I want to set my ISO at a specific value then the camera LCD/EVF shows a totally different value. For example, I have shutter manual, aperture manual and ISO dial at 6400, the camera shows ISO at 4000, when I take pictures it will show ISO at 4000 and not 6400. When I try to choose another ISO value it will skip some of the available values that are shown on the dial. Another issue I am having is when my exposure dial is not set at specific value, then I cannot set ISO to Auto no matter what value I select on the dial. If I do select the different exposure compensation values, then I choose A for ISO, the camera will activate the front commend dial to manually change ISO values. To get in Auto ISO, the shutter speed cannot be set in auto and the ISO dial should be set at 125, when I turn the ISO wheel, it seems like the numbers are misaligned by one value, If I put the dial on A with shutter speed manual, then it will trigger the front commend dial. The other issue that I am having is when I have Aperture, shutter speed and ISO on manual, If I change the exposure dial compensation + or - , it actually changes the exposure of the picture as well as the ISO value, which as I understand, if Camera is in full manual, the exposure dial should do nothing. The last issue that I am having, if I do have ISO in manual at a set value, and adjust exposure compensation dial, it alters my ISO instead of my shutter speed or my aperture, even though ISO is in Manual and the other two dials are in Automatic. I am not really sure if all of this is by design and I am just not understanding how everything works together, but it seems really odd how everything changes. Resetting the camera settings didn’t help. 
    • FSND
      Remote Release suddenly stopped working

      By FSND · Posted

      I also have the eaxct problem with my X-T5. The remote used to work, but not anymore. I also get the light coming on on the camera back, and autofocus will happen, but no shutter release. Since I use the 2 or 10 seconds timer more I don't know if a firmware update is the cause of this negative change. I actualley only use the wired jack-remote for action release on a tripod.  Did anybody find a cause, and even more assisting, a solution?
    • mahidoes
      X-T5 always shows firmware update menu when turned on

      By mahidoes · Posted

      I have the same issue. Have you found the the solution?
    • jerryy
      landscapes with fuji x

      By jerryy · Posted

      Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

       
    • Rich Martin
      OVF magnification

      By Rich Martin · Posted

      On my XPro 2 the rear command dial, when pressed, can cycle through 3 different magnification levels in the OVF.  
×
×
  • Create New...