Jump to content

AF after firmware update

littleego

By littleego
in Fuji X-T5 / Fuji X-T50

 Share

Recommended Posts

littleego Newbie

littleego

Posted
Posted

Hi all - I recently tried to like an X-T5 and in fact did very much, but ended up returning it because I could NOT get the continuous/eye/face AF to work at all. I had a nearly 0% hit rate, with images usually focusing several inches in-front of or behind the subject, despite confirmation from the little green box in the viewfinder. Manual focus was also a mess for anything that moves, without quite enough EVF resolution for me and some motor jumping in the lenses with non-linear motors. 

Anyone tried the AF with the new firmware, and if so do you see real improvements?

Link to post
Share on other sites
littleego Newbie

littleego

Posted
  • Author
Posted
9 minutes ago, Nikkon said:

I tried and it works for me. I suppose you enabled eye traking already.

what is the AF preset you are using?

 

 

Yes, tried eye AF with all the various settings I could think of. Consistently got green box confirmation in the viewfinder, but the photos were not actually focused on the eye, ever. 

I no longer have the camera, because of that. 

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Content

  • Posts

    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Thank you. I will research it.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Typically you need to make sure the lens is compatible with the camera, i.e. check the lens compatibility charts for your camera, then make sure the respective firmwares are updated so older issues are resolved. After that, each lens has a manufacturer’s profile which will be embedded into the raw file meta data for the images captured using that lens. From there, it is up to the raw conversion software to apply the lens correction to the image. Different converters do that differently, some automatically, some only if a setting is turned on. For in-camera jpegs, the on-board converter does the corrections automatically, assuming the camera recognizes the lens, it applies a generic profile otherwise. I do not know if that can be turned off or not.
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      How does one make sure that Fuji's image correction is turned on to correct barrel and pin-cushion distortion on a GFX 100 or GFX100S when using the GF20-35? Is it only applied to the jpegs and not to the raw files? (I was surprised to discover the barrel distortion on the GF 35-70mm lens.) I normally shoot in raw with jpeg back-up and use the raw files, which I convert either in Affinity Photo 2 when editing with that program or in Raw File Converter Ex 3.0 by Silkypix if I wish to process the image in Photoshop CS6. (Adobe DNG is also a possibility.) Thank you for the help. Trevor
×
×
  • Create New...