Jump to content

Recommended Posts

Hey everyone! New to Fuji and the forums. I bought myself a X-T20 18-55mm kit and would like to use it in the winter sometimes. I know its not weather sealed like the X-T2 but would it still be safe to use in colder weather. I have a Pelican Case from my previous DSLR and was planning to put it in the case outside in the cold after shooting, before entering indoors to warmer temperatures. Would this be enough to protect the camera for damage with drastic temperature change? I plan to go yurting in the winter. 

 

Cheers!

Link to post
Share on other sites

Often cold weather means dry air, so less risk than in warmer, tropical countries. Condensation can be a risk when bringing cold equipment back indoors.

 

The key issue from cold is batteries, as they lose power as the temperature drops. This impacts all cameras, weathersealed or not. Try to keep spare batteries in your pocket, and have extra spares.

Link to post
Share on other sites

  • 1 month later...

Weather Sealing is poopoo.  Ask ANYONE who has done serious repair work on ANY camera or lens and they will laugh at you.

 

Sooner or later, you will pay the price for shooting in bad weather.   With that having been said, my daughter is on a six month contract up about 330 miles NW of Anchorage Alaska.  The weather this week, without windchill factor, is 25 degrees below zero.  And, she "borrowed" my X-T1 with the 18-55 and that's what she uses every day to and from work in the village she works at.

 

So other than batteries not functioning a fulll capacity, it's a no-big-deal scenario.  For Fuji, or pretty much any other camera.  My Fuji's both X-T1, X-T2 have been used in the extreme opposite was well -- over 100 degrees Fahrenheit, humid, temperature again with no ill-effects.  Both for extreme heat, and cold, when bringing gear back in or taking it outside is to make sure you have it wrapped in what I use:  ZipLockbags.  Once you go outdoors, or back indoors, give it 10 minutes or so to acclimate to the cold, or warm temperature difference.

Link to post
Share on other sites

Just returned from a month in Europe (UK & Prague) & I live in Western Australia so Prague was very cold & London positively mediterranean in comparison. My cameras have worked without problems in temps of -5C (not Alaska cold) to +40C without problems other than the lens misting over on the outside immediately on leaving  the warmth of the hotel.

Edited by TonyB
Link to post
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

  • Posts

    • I also use a Nikon to GFX Fringer and it works very well.  24mm f/1.8 vignettes so best used on 35mm mode.  50mm f/1.8 covers the entire frame very well with no issues and is a superb little lens. 105mm Sigma vignettes slightly but is perfectly usable. 300 f/4 likewise the 105.  I have a 70-200 f/20+.8 incoming to test so will report back but I'm expecting a little vignetting.  Even in 35mm mode the image is still 60MP and if you're prepared to manually crop and correct you can get 80-90 MP images.  I also have a C/Y to GFX adapter.  The 24mm Sigma Superwide vignettes strongly. Ditto 28-80 Zeiss Sonnar. 80-200 f/4 Sonnar is perfectly usable. All work fine as 35mm mode lenses.  I also have an M42 adapter which I tried with the Carl Zeiss Jena 135mm f/3.5 with good results. 
    • Thank you. I will research it.
    • Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
    • Typically you need to make sure the lens is compatible with the camera, i.e. check the lens compatibility charts for your camera, then make sure the respective firmwares are updated so older issues are resolved. After that, each lens has a manufacturer’s profile which will be embedded into the raw file meta data for the images captured using that lens. From there, it is up to the raw conversion software to apply the lens correction to the image. Different converters do that differently, some automatically, some only if a setting is turned on. For in-camera jpegs, the on-board converter does the corrections automatically, assuming the camera recognizes the lens, it applies a generic profile otherwise. I do not know if that can be turned off or not.
×
×
  • Create New...