Jump to content

Recommended Posts

Hey everyone! New to Fuji and the forums. I bought myself a X-T20 18-55mm kit and would like to use it in the winter sometimes. I know its not weather sealed like the X-T2 but would it still be safe to use in colder weather. I have a Pelican Case from my previous DSLR and was planning to put it in the case outside in the cold after shooting, before entering indoors to warmer temperatures. Would this be enough to protect the camera for damage with drastic temperature change? I plan to go yurting in the winter. 

 

Cheers!

Link to post
Share on other sites

Often cold weather means dry air, so less risk than in warmer, tropical countries. Condensation can be a risk when bringing cold equipment back indoors.

 

The key issue from cold is batteries, as they lose power as the temperature drops. This impacts all cameras, weathersealed or not. Try to keep spare batteries in your pocket, and have extra spares.

Link to post
Share on other sites

  • 1 month later...

Weather Sealing is poopoo.  Ask ANYONE who has done serious repair work on ANY camera or lens and they will laugh at you.

 

Sooner or later, you will pay the price for shooting in bad weather.   With that having been said, my daughter is on a six month contract up about 330 miles NW of Anchorage Alaska.  The weather this week, without windchill factor, is 25 degrees below zero.  And, she "borrowed" my X-T1 with the 18-55 and that's what she uses every day to and from work in the village she works at.

 

So other than batteries not functioning a fulll capacity, it's a no-big-deal scenario.  For Fuji, or pretty much any other camera.  My Fuji's both X-T1, X-T2 have been used in the extreme opposite was well -- over 100 degrees Fahrenheit, humid, temperature again with no ill-effects.  Both for extreme heat, and cold, when bringing gear back in or taking it outside is to make sure you have it wrapped in what I use:  ZipLockbags.  Once you go outdoors, or back indoors, give it 10 minutes or so to acclimate to the cold, or warm temperature difference.

Link to post
Share on other sites

Just returned from a month in Europe (UK & Prague) & I live in Western Australia so Prague was very cold & London positively mediterranean in comparison. My cameras have worked without problems in temps of -5C (not Alaska cold) to +40C without problems other than the lens misting over on the outside immediately on leaving  the warmth of the hotel.

Edited by TonyB
Link to post
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

  • Posts

    • True. For me the problem is that it is quite difficult to infer from EVF what the outcome will be. Of course, you can get some impression as to how the scene will be exposed, and then you can adjust the settings (exposure). To me, you need to make several different exposures in certain situations, as you cannot, however, determine correctly the one by just looking at EVF. I find this laborious for some holiday pictures etc... The "important" pictures I always take in Raw. I din't find this problem with my Nikon D7100. So I have needed to adapt to this new situation. 😃
    • I only started at 400 ISO to trigger the dynamic range setting on the X-H2 and agree higher ISO will be good for capturing crisp waves I depend on exposure compensation a lot too. For sunsets at the beach, I usually shoot them on a tripod, rarely handheld. At higher ISO, the noise can be considerable when rescuing shadows so I will probably only go up to ~1200.  The closed aperture is to control the amount of light from shooting direct in the sun and create a wide depth of field, but I also agree, dialing back to f/11 or f/8 could work when the sun is very low on the horizon.  I spot meter on the sun, then dial in the exposure compensation to bring up the shadows. Maybe this isn't a good approach, but it seems to work. I think I just need to be more aggressive with the exposure compensation and see what happens. I may have a chance tonight at a different location on the coast and will post my findings. Thanks for the advice.
    • I recently updated my Pixel 6 to a Pixel 10. Now no more connection issues. I'll never know why. Both phones were running Android 16.
    • It's similar to what happens to my XT-5 and Oneplus phone. For those of us with OnePlus/Oppo phones we get told the connection has been lost. So it might be another aspect of the problem, though so far at least it has looked like Samsung and Google phones were working OK. Judging by the number of people who have problems after firmware updates, I find it difficult to understand why Fuji can't make it possible to downgrade. At least then you could back out of something nasty.  Good luck. 
    • Well I have seemed to found the solution. SetUp-Screen setup-EVF Brightness-Auto/Manual. It was set on auto. However, when I choose "manual" and tried to make an adjustment is said "check the finder." While this did not allow me make any adjustments the EVF was substantially brighter. Problem solved. I wish to thank all the help I gave to myself concerning this matter. 🙄 (Actually I just got lucky before someone pointed all this out.)
×
×
  • Create New...