Jump to content

Recommended Posts

I have also have an XF 150-600 that I use for wildlife videography--mostly birds.  That lens has vignetting from 400 mm - 600 mm when shot at the largest aperture.  In general, I do not notice the vignetting with little sky involved.  However, If I have a bird against a bald sky (frequent occurrence in Arizona) I can have wild vignetting that bounces all over the place.  The only solution is to stop down to f/11 which corrects the issue.  For video, the X-H2S does have peripheral correction.  However, it does not seem to work at 400 mm and above.  I have tried with peripheral correction on and off.  Makes no difference--it just does not work.

I did some research on long telephoto zoom lens and vignetting.  Regardless of company (Sony FE 200-600, Nikon 180-600, Canon 200-800), all suffer from vignetting at their longest focal lengths and wide open--it is function of the design. The solution on all of these lens is to stop down by 1 stop where it virtually disappears.  Based on reports, the amount of vignetting for the XF 150-600 is on the low end from all of the reports that I have read--but then again I would expect it to be lower because this is an APS-C camera.

Hope this helps others,

Don

 

 

 

Edited by Don Barar
Link to post
Share on other sites

All lenses are a compromise where the designer has to decide what is most important to correct. Most modern lenses, particularly zooms, rely on software to reduce some faults. This allows the lens designers more leeway to address other problems. Vignetting is usually on the list. It will be corrected in the camera in the case of jpegs or in the software in the case of raw output. If you use raw check that automatic lens correction is enabled.

Link to post
Share on other sites

  • 1 month later...
On 6/14/2025 at 9:54 PM, Zack1952 said:

All of a sudden, I’m getting vignetting with both Fujifilm 18-135 and 55-200.  I don’t use lens hoods so that’s not the cause.  Thoughts anyone?

I had the same problem.  Turned out that my Drive Dial was on ADV and therefor activated a filter (Toy Camera in my case) .....  

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Content

  • Posts

    • Hey everyone, I am new to the fujifilm system, and I just received my X100vi about 15 days ago, and yesterday I noticed that ISO and exposure dials are acting up. I spent hours watching YouTube videos and reading forms without finding any solutions. Using ChatGPT or Gemini also didn’t help. My issues are the following: If I want to set my ISO at a specific value then the camera LCD/EVF shows a totally different value. For example, I have shutter manual, aperture manual and ISO dial at 6400, the camera shows ISO at 4000, when I take pictures it will show ISO at 4000 and not 6400. When I try to choose another ISO value it will skip some of the available values that are shown on the dial. Another issue I am having is when my exposure dial is not set at specific value, then I cannot set ISO to Auto no matter what value I select on the dial. If I do select the different exposure compensation values, then I choose A for ISO, the camera will activate the front commend dial to manually change ISO values. To get in Auto ISO, the shutter speed cannot be set in auto and the ISO dial should be set at 125, when I turn the ISO wheel, it seems like the numbers are misaligned by one value, If I put the dial on A with shutter speed manual, then it will trigger the front commend dial. The other issue that I am having is when I have Aperture, shutter speed and ISO on manual, If I change the exposure dial compensation + or - , it actually changes the exposure of the picture as well as the ISO value, which as I understand, if Camera is in full manual, the exposure dial should do nothing. The last issue that I am having, if I do have ISO in manual at a set value, and adjust exposure compensation dial, it alters my ISO instead of my shutter speed or my aperture, even though ISO is in Manual and the other two dials are in Automatic. I am not really sure if all of this is by design and I am just not understanding how everything works together, but it seems really odd how everything changes. Resetting the camera settings didn’t help. 
    • I also have the eaxct problem with my X-T5. The remote used to work, but not anymore. I also get the light coming on on the camera back, and autofocus will happen, but no shutter release. Since I use the 2 or 10 seconds timer more I don't know if a firmware update is the cause of this negative change. I actualley only use the wired jack-remote for action release on a tripod.  Did anybody find a cause, and even more assisting, a solution?
    • I have the same issue. Have you found the the solution?
    • Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

       
    • On my XPro 2 the rear command dial, when pressed, can cycle through 3 different magnification levels in the OVF.  
×
×
  • Create New...