Jump to content

X-T3 Shutter curtain stuck

tahitizoom
 Share

Recommended Posts

tahitizoom Apprentice

tahitizoom

Posted
Posted

Hi

After 1 year the shutter curtain stuck followed with the "Turn Off/On" message (I had my newly purchased 16mmf1.4 lens attached). Turning the camera on/off and resetting didn't help. The shutter stays in the closed position. Please, How to fix it ? 

Thank you for help.

stephane

Link to post
Share on other sites
jerryy Grand Master

jerryy

Posted
Posted (edited)

Have you tried the 'hard' reset (write down the list of your current settings, pull the batteries out, set it on a shelf for several days and resist the urge to check on it until after several days go by -- several meaning at least four instead of three)? The 'hard' reset option usually causes all the settings to go back to the out-of-the-box factory settings.

There is a small chip on the camera board that stores the settings, it is powered by the main battery which is backed up by a capacitor that powers the chip for a short time when the main batteries are pulled out, such as when you swap them out. Once the capacitor is drained, (this can take a while) settings are supposed return to factory fresh defaults.

If that option fails, the settings chip may need a visit to your camera dealer's repair shop.

Edited by jerryy
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Content

  • Posts

    • thelostkiwi
      Looking for Full Frame lenses to adapt to GFX

      By thelostkiwi · Posted

      I also use a Nikon to GFX Fringer and it works very well.  24mm f/1.8 vignettes so best used on 35mm mode.  50mm f/1.8 covers the entire frame very well with no issues and is a superb little lens. 105mm Sigma vignettes slightly but is perfectly usable. 300 f/4 likewise the 105.  I have a 70-200 f/20+.8 incoming to test so will report back but I'm expecting a little vignetting.  Even in 35mm mode the image is still 60MP and if you're prepared to manually crop and correct you can get 80-90 MP images.  I also have a C/Y to GFX adapter.  The 24mm Sigma Superwide vignettes strongly. Ditto 28-80 Zeiss Sonnar. 80-200 f/4 Sonnar is perfectly usable. All work fine as 35mm mode lenses.  I also have an M42 adapter which I tried with the Carl Zeiss Jena 135mm f/3.5 with good results. 
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Thank you. I will research it.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Typically you need to make sure the lens is compatible with the camera, i.e. check the lens compatibility charts for your camera, then make sure the respective firmwares are updated so older issues are resolved. After that, each lens has a manufacturer’s profile which will be embedded into the raw file meta data for the images captured using that lens. From there, it is up to the raw conversion software to apply the lens correction to the image. Different converters do that differently, some automatically, some only if a setting is turned on. For in-camera jpegs, the on-board converter does the corrections automatically, assuming the camera recognizes the lens, it applies a generic profile otherwise. I do not know if that can be turned off or not.
×
×
  • Create New...