Jump to content

RoboSHOOT sync speeds with the x100 series works at all speeds up to 1/4000s

Patrick FR

By Patrick FR
in Flash Photography with Fuji X

 Share

Recommended Posts

Patrick FR Veteran

Patrick FR

Posted
Posted

Press Release:

This is a brief update about RoboSHOOT© flash Triggers for Fuji
What sync speed can you expect with the x100? We've frequently gotten this question and the answer is complex enough that it warrants this notice.

We've tested on both X100s and X100T and found synch speeds work all the way to 1/4000s. So, yes, RoboSHOOT© supports all shutter speeds on these cameras.

But, there are things to be aware of. Firstly, at higher flash power the flash duration can be longer than 1/1000s. So, you will frequently see brightness fall off starting at 1/1000s, especially if the aperture is stopped down (because more power is requested). Secondly, the longer the flash duration, the more sensitive it is to any delay (there is about 500 microseconds of delay from the radio). Lastly, the camera only requests so much power, so again, stopping down reaches a limit. Thus, these three physical limitations come into play to affect the exposure, and they compound when multiple limitations occur. So, practically, what does this mean?

RoboSHOOT© does supports TTL on the X100 series throughout the shutter speed range: no HSS required. However, at very high speeds (about 1/1000s and above) you may want to keep the aperture wide-open, and regardless, you may see under exposure at extreme speeds. Of course, some of this can be compensated for with flash exposure compensation. So, enjoy experimenting with this fun option!

Link to post
Share on other sites
Lino Apprentice

Lino

Posted
Posted

I use a cheap IR hotshoe adapter from Walimex (model CY-20YS) since the first day i got my camera and it really syncs at 1/4000 every time - yes, it's impressive how it works.
The only disadvantage is the red cast fired from the trigger when i take a picture, and, of course, the usage outdoor in bright sun it's almost impossible.
Anyway, it's good to have news like these, as i can use the highest sync speed of my X100s without the problems i have nowadays! :)

Cheers,

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Content

  • Posts

    • thelostkiwi
      Looking for Full Frame lenses to adapt to GFX

      By thelostkiwi · Posted

      I also use a Nikon to GFX Fringer and it works very well.  24mm f/1.8 vignettes so best used on 35mm mode.  50mm f/1.8 covers the entire frame very well with no issues and is a superb little lens. 105mm Sigma vignettes slightly but is perfectly usable. 300 f/4 likewise the 105.  I have a 70-200 f/20+.8 incoming to test so will report back but I'm expecting a little vignetting.  Even in 35mm mode the image is still 60MP and if you're prepared to manually crop and correct you can get 80-90 MP images.  I also have a C/Y to GFX adapter.  The 24mm Sigma Superwide vignettes strongly. Ditto 28-80 Zeiss Sonnar. 80-200 f/4 Sonnar is perfectly usable. All work fine as 35mm mode lenses.  I also have an M42 adapter which I tried with the Carl Zeiss Jena 135mm f/3.5 with good results. 
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Thank you. I will research it.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Typically you need to make sure the lens is compatible with the camera, i.e. check the lens compatibility charts for your camera, then make sure the respective firmwares are updated so older issues are resolved. After that, each lens has a manufacturer’s profile which will be embedded into the raw file meta data for the images captured using that lens. From there, it is up to the raw conversion software to apply the lens correction to the image. Different converters do that differently, some automatically, some only if a setting is turned on. For in-camera jpegs, the on-board converter does the corrections automatically, assuming the camera recognizes the lens, it applies a generic profile otherwise. I do not know if that can be turned off or not.
×
×
  • Create New...