Jump to content

Intermittent rear lcd blackout

ethanamongstfriends
 Share

Recommended Posts

ethanamongstfriends Newbie

ethanamongstfriends

Posted
Posted

I recently experienced intermittent LCD blackout where the lcd refused to respond. Usually I would just switch the camera off and back on to rectify it. On the last occasion I had to leave the camera off for a few minutes to get the lcd to respond. One thing I have noted is that when the LCD refused to respond the camera still behaved perfectly using the EVF and continued to take pictures. The only other place I have seen this issue mentioned is on IamtheJeff when he lists what he believes to be firmware problems. Has anybody else encountered this?

Link to post
Share on other sites
milandro Grand Master

milandro

Posted
Posted

is it possible that something activates the sensor which toggles between LCD and EVF (if you’ve set the camera to work with this?).

 

http://fujifilm-dsc.com/en-int/manual/x-e2s/menu_setup/evf_lcd/index.html

 

“....The eye sensor turns the viewfinder on when you put your eye to the viewfinder and turns it off when you take your eye away (note that the eye sensor may respond to objects other than your eye or to light shining directly on the sensor). If automatic display selection is enabled, the LCD monitor will turn on when the viewfinder turns off...."

Link to post
Share on other sites
  • 2 months later...
tkhengong Newbie

tkhengong

Posted
Posted

My X-T2 is only 1 week old. I have experienced this issue too just this morning. I had the LCD screen tilted out at 45% angle when I faced this problem between shots. Moving the LCD screen back to its rest position got the LCD screen activated again. 

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Content

  • Posts

    • Giampaolo Masserano
      Looking for Full Frame lenses to adapt to GFX

      By Giampaolo Masserano · Posted

      I use a TECHART ring to mount Canon EF lenses on the GFX 50S-II and 100S-II, maintaining image stabilization and autofocus. The only limitation are lenses with a small rear element diameter that make it impossible to cover medium format. Fast lenses like the EF 85/1.2L or the 100-400L, however, work great.
    • thelostkiwi
      Looking for Full Frame lenses to adapt to GFX

      By thelostkiwi · Posted

      I also use a Nikon to GFX Fringer and it works very well.  24mm f/1.8 vignettes so best used on 35mm mode.  50mm f/1.8 covers the entire frame very well with no issues and is a superb little lens. 105mm Sigma vignettes slightly but is perfectly usable. 300 f/4 likewise the 105.  I have a 70-200 f/20+.8 incoming to test so will report back but I'm expecting a little vignetting.  Even in 35mm mode the image is still 60MP and if you're prepared to manually crop and correct you can get 80-90 MP images.  I also have a C/Y to GFX adapter.  The 24mm Sigma Superwide vignettes strongly. Ditto 28-80 Zeiss Sonnar. 80-200 f/4 Sonnar is perfectly usable. All work fine as 35mm mode lenses.  I also have an M42 adapter which I tried with the Carl Zeiss Jena 135mm f/3.5 with good results. 
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Thank you. I will research it.
    • jerryy
      Image correction with GF20-35

      By jerryy · Posted

      Ahh, the infamous brick wall photos… 😀 According to internet lore, if the dng converter does not properly apply the corrections, you can have it apply custom profiles that should work for you. How to do that is waaaaaay outside of this comment’s scope, but there are plenty of sites listed in the search engines that step you through the processes. Best wishes.
    • Trevor R
      Image correction with GF20-35

      By Trevor R · Posted

      Jerry Thank you very much. That is extremely helpful. It seems that the camera and the lens have the latest firmware update, so it appears that the corrections should be applied automatically. The lens arrived this afternoon and I took some quick test shots, in which the correct lens information appeared in the EXIF files, so that sounds good. I used Adobe DNG converter to convert the Raw (RAF) files, and then opened the DNG files and saved them in PSD format. However, with a beautiful, clear, cloudless blue sky, there were no lines near the edges to check if distortion had been corrected. Another day I plan to photograph a brick wall. Thank you for your help.
×
×
  • Create New...