Jump to content

X-T2 LCD and EVF Color Tint


howardgf

Recommended Posts

I've owned an X-T2 now for over 3 years and used an X-T1 as my just-in-case travel backup. I sold the X-T1 and bought another X-T2 from a highly rated seller on Fred Miranda who is divorcing Fuji for Nikon mirrorless. When I received the second X-T2 I bought I was checking it out and noticed that the live image viewed on the LCD and through the EVF, with both my and the newly acquired cameras set to monochrome, had what I would describe as a-kind-of sepia tint. This is also true when viewing the menu screen on both the LCD and EVF. My original X-T2 looked pure black and white while the one I just bought did not display the same tonality. I checked the screen settings for both cameras' LCD and EVF color and brightness settings and they are both the same, all 0's.

So I'm questioning is it normal to have this disparity between two exact same models, or is the one I just bought defective?

Edited by howardgf
Formatting
Link to post
Share on other sites

Has the White Balance setting been shifted to a warmer tone? Go into WB and click the arrow on the right of your chosen setting to bring up the WB shift screen. It's easy to accidentally move the point off-centre.

Edited by dfaye
sentence correction
Link to post
Share on other sites

4 hours ago, dfaye said:

Has the White Balance setting been shifted to a warmer tone? Go into WB and click the arrow on the right of your chosen setting to bring up the WB shift screen. It's easy to accidentally move the point off-centre.

Thanks for replying.  Yes, it was.  But centering the WB had no visible effect on the tonality difference I'm seeing between the two cameras.  I guess if I were not looking at both cameras I wouldn't know the difference existed.  I'm going to take a controlled black and white shot with each camera of a lens calibration test board to see if there is any difference in the image tonality.  Any other suggestions are welcome.

Link to post
Share on other sites

I'd also check if both cameras have same firmware. But thechically it should be just slightly different screen hardware.

I have two exact model mobile phones purchased with a 1 year gap. One phone shows slightly warmer tones comparing to the other one.

Another assumption is that EVF/LCD screen may slighly change the tint due to the screen age.

And my last assumption is - if there is any protective screen film/glass, it may also influence color tint.

I personally think there are nothing wrong with your second camera, and test image results should show exact 100% color match.

 

Link to post
Share on other sites

5 hours ago, yukosteel said:

I'd also check if both cameras have same firmware. But thechically it should be just slightly different screen hardware.

I have two exact model mobile phones purchased with a 1 year gap. One phone shows slightly warmer tones comparing to the other one.

Another assumption is that EVF/LCD screen may slighly change the tint due to the screen age.

And my last assumption is - if there is any protective screen film/glass, it may also influence color tint.

I personally think there are nothing wrong with your second camera, and test image results should show exact 100% color match.

 

Both are running the same firmware.  I took test shots with each under controlled conditions and am satisfied the images from both look almost identical.  Thanks for your suggestions. 

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

  • Posts

    • Does it use wi-fi when you are not specifically attempting to transfer files?
    • Hello dear Fujifolks - I come from 54 years of shooting Nikon cameras, and this is my first Fujifilm experience as I've just sold my Nikon D7200 in exchange for a tiny but endearing X-T20. Very pleased with it as it's so lightweight, but very well built. But takes some getting used to the menus and settings after Nikon's DSLR functional simplicity ! I'm working on it though and slowly coming to terms with the new system. My question for now is this: is there any way to turn OFF the wifi antenna in the camera ? I'm particularly wifi signal sensitive and have no intention of using that function as I do all my editing and printing on my PC. I've checked the wifi menu options but cannot find a simple wifi ON-OFF selector. Thanks for your help and I'll be back with more Q's when needed. Blessings to you all... 
    • Has anyone successfully used pocket wizards with an XT5? I cannot get it to fire.  Do Fujis and pocket wizards get along? Thanks in advance for your wisdom on this, kind readers!
    • Grzegorz, Go to the Networking Setting in your camera menu (the last one at the bottom - unless you have a My Menu then that is the last one). There, go to Network Setting and choose the SSID (name) of your WiFi network, type in the password, choose "SET". If you have a functioning DHCP server on your network, the camera should get its IP address (and Subnet_Mask and Gateway). If not, you can enter these manually. It is a little tricky, there will be some zeros already here, move the cursor after the zero and use DEL to delete it and make space in the input fields for your own correct values. If you do not know what to enter, have a look at values in the network settings of your computer and use the same except for the IP address, try some fairly higher number, hopefully you hit an unused one. Usually the values would be something like IP: 192.168.1.188, Subnet Mask: 255.255.255.0, Gateway IP: 192.168.1.1  or something like that, take clues from your computer. The camera and computer must be on the same network. Then in Connection Mode on the camera, choose Wireless Tethering Fixed. And half-press the shutter to exit the menu and get in shooting mode. The red LED should be blinking. If you can look at your network devices, e.g. on your router, you should see the camera there. You can see check the camera settings in the camera menu in the INFORMATION item of the Network Setting menu to see the MAC address of your camera and look for it in the list of devices on your network.  Then use the tethering in your software, e.g. in Capture One. The camera may not show immediately, take a shot and then it should show in the list of available cameras. Good luck. Report back how did you fare.  PS If you have a Windows machine, you need to have Bonjour installed and running. Macs have it.
    • Hey all, I just got my first camera. The X-T30 II. It seems the Eye Sensor + LCD Image Display view-mode is doing the exact same thing as just the Eye Sensor view-mode setting. Any ideas why this is or what's supposed to be happening? Firmware Version: 2.04
×
×
  • Create New...