Jump to content

infra red


daveat22

Recommended Posts

All cameras will respond to infra red light. If you take infra red photos the way you describe your exposure times will be considerably longer for a given ISO. This is because not only does the infra red filter block almost all the light in the visible spectrum but there is a filter on the camera's sensor that blocks infra red light so not a lot of the light entering your lens reaches the sensor. At least the XT-2 has an electronic viewfinder so you should still have a reasonable view for framing etc.

 

If you just want to try infra red photography the cokin IR filter will be OK. Just be prepared to either bump up your ISO (a lot) or use a tripod.

 

If you decide to get into infra red photography, you might be better buying a body that's been converted for IR or paying for a conversion. IR conversion is basically removing the IR blocking filter from the sensor. You can choose to replace the IR blocking filter with an infrared filter at the sensor (that's what I have done) or you can just remove the IR blocking sensor and replace it with clear glass and use an IR filter on your lens. There are pros and cons for both.

 

Google infra red photography to find some websites that can provide more detailed advice.

Link to post
Share on other sites

I'm not sure which sensor your camera uses but I found that different Fuji sensors make a lot of difference in IR effect.  My X100s was sensitive enough to take hand held IR in bright sunlight with a 720nm filter.  I have had no IR luck at all with my X100F, which uses a different sensor.  All that I have tried would be classified as poor images.

 

Even though the X100s was decent, I had it converted two years ago and never looked back.  Now I carry both cameras on most of my photo adventures.

Edited by neal3K
Link to post
Share on other sites

Thanks Col and Neal for that information I found it interesting.

I am not a great IR enthusiast but I have seen some images recently which I found very interesting bordering on artistic. So I thought i would try IR on the cheap  by buying the Cokin IR filter and using it in a P holder. 

I do love long exposure images particularly at the seaside and this would suit this filter as I could use it in conjunction with a 10 stop ND and make the exposure very long, and I have heard that the X-T2 will also take IR with  high ISO settings. Incidentally i would be converting to mono as I really do not like colour IR it looks so false to me.

Link to post
Share on other sites

I bought the Cokin IR filter and took some images today but there was no infra red effect what so ever. I used a post processing technique as described by Scott Photographics but I couldn't get anything like an infra red effect with green leaves showing as white.

Link to post
Share on other sites

When I was having trouble, I got this in response to a comment using a 590 filter.

 

I would not expect good results from a 590nm filter when using any non converted camera, the light from 590-690nm will be recorded fairly well while the NIR will be less than 1% of that even with a fairly IR sensitive camera.

 

That is why I was asking.  Since your seems to be a 650nm filter, it should let very little visible light in.

 

​Let's correspond at my email and perhaps you can send some of your images.  nwellons@hotmail.com

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

  • Posts

    • Looking more like the next Fuji camera we see will be an X-T50 but it is still a rumor and no specs have been published.
    • Hey guys, The shutter on/off button switch may be loose on mine. After turning camera on and pressing the shutter/holding close to the area, the camera will turn off and say 'sensor cleaning'. This doesn't happen if I'm shooting via touch screen at all. Everything else is functional. Anyone else experience this before? Would love a much cheaper fix since Fuji Canada just quoted me $700 CAD to fix it, and considering everything else is functional except that part I'm not even sure why MPMB Main Board parts is being replaced😕 I got no explanation from them either.
    • As far as I know the firmware is not country specific. Are you sure that the filename has not been changed ( I am told this can happen with mac os). That's the only thing I can think of.
    • My x-t5 does not exhibit the focusing switch behaviour as you report it, so that is very strange and indicative of a fault. It does not matter whether the flash is attached or not. Once you set the camera for your studio flash, say 1/250th at f5.6, the camera, which is showing you what you will get at that exposure without the flash, will show a black screen unless the ambient light is brighter than what you would typically get indoors. That is why, as Jerry says, you have to set preview exp/wb to off. I have set a button for this.
    • I connected to FRAME.IO a while back and it works fine, but the camera wouldn't connect to the internet all of a sudden today and would get stuck on the reset screen, including initializing and even switching USB Connection mode. Is anyone else experiencing the same thing?
×
×
  • Create New...