Jump to content

Tried to update 2.0 Firmware - Card Error Message ( October 6)


Recommended Posts

Not sure if it's related or fluke. I loaded the new 2.0 firmware onto a freshly formatted card. Inserted the card and got an error message "CARD ERROR". So I took  that card out and put the old one back in. Now same message.. With every Card.

 

I was using Slot 1 and slot 2 as JPG. SO I removed the card and set it for Sequential and put the card into slot 2. Works fine in slot 2. Slot 1 is dead. Just error message when I try anything in it. "CARD ERROR".

 

any suggestions. 

Link to post
Share on other sites

Happened once during my fw upgrade yesterday. I upgraded the fw to 2.00 first, then in the process of upgrading the XF35/1.4 this happened. Turned the camera off, then on, did a couple of exposures which worked fine, then turned it off again. Holding in DISP/BACK when turning it on again showed the expected fw upgrade screen. Hope it works for you.

Link to post
Share on other sites

Happened once during my fw upgrade yesterday. I upgraded the fw to 2.00 first, then in the process of upgrading the XF35/1.4 this happened. Turned the camera off, then on, did a couple of exposures which worked fine, then turned it off again. Holding in DISP/BACK when turning it on again showed the expected fw upgrade screen. Hope it works for you.

 

Thanks, Tried that and a hundred other things. Did a hard reset. Took it to the camera shop I purchased it at and now its on its way to Fuji fro repairs.

Link to post
Share on other sites

  • 2 months later...

So just an update.

 

I ended up having to send the camera back to Fuji. They repaired it. What had happened was a small piece of my SD card had lodged in the card slot and was preventing the card and camera from communicating.  They repaired it no charge, even though they didn't have to. 

 

Another reason I love FujiFIlm.

 

Working great now.

Link to post
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

  • Posts

    • Looking more like the next Fuji camera we see will be an X-T50 but it is still a rumor and no specs have been published.
    • Hey guys, The shutter on/off button switch may be loose on mine. After turning camera on and pressing the shutter/holding close to the area, the camera will turn off and say 'sensor cleaning'. This doesn't happen if I'm shooting via touch screen at all. Everything else is functional. Anyone else experience this before? Would love a much cheaper fix since Fuji Canada just quoted me $700 CAD to fix it, and considering everything else is functional except that part I'm not even sure why MPMB Main Board parts is being replaced😕 I got no explanation from them either.
    • As far as I know the firmware is not country specific. Are you sure that the filename has not been changed ( I am told this can happen with mac os). That's the only thing I can think of.
    • My x-t5 does not exhibit the focusing switch behaviour as you report it, so that is very strange and indicative of a fault. It does not matter whether the flash is attached or not. Once you set the camera for your studio flash, say 1/250th at f5.6, the camera, which is showing you what you will get at that exposure without the flash, will show a black screen unless the ambient light is brighter than what you would typically get indoors. That is why, as Jerry says, you have to set preview exp/wb to off. I have set a button for this.
    • I connected to FRAME.IO a while back and it works fine, but the camera wouldn't connect to the internet all of a sudden today and would get stuck on the reset screen, including initializing and even switching USB Connection mode. Is anyone else experiencing the same thing?
×
×
  • Create New...