Jump to content

Firmware 1.23 camera stucked, big issue with EVF and shutdown.


Théotim
 Share

Recommended Posts

Advertisement (gone after registration)

Hi all !

After updating via app (1.23) my brand new x-t4 (work like a charm with 1.22 firmware) the EVF doesn't work at all now and if i try to switch to the EVF view every thing goes black and the camera get stuck like that forever... Even if i try to reboot it, the only option is to plug out/plug in the battery. Impossible to go back to the previous firmware (what a shame on a 2000€ camera). I'm very frustrated my camera is unusable... I update again the firmware with the classic SD option, the process finish the update without a problem but the problem persist cannot do anything with it now. If the camera go sleep... Stucked. If the eye sensor is activated for the EVF... Stucked. If i try to shutdown the camera... Stucked. 

Thank you in advance.

Best regard.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

  • Similar Content

    • By Creativestubble
      Hi all,

      Second post here would appreciate the input. I just purchased an X-T3 and X-H1.
      The EVFs on paper are meant to be the same with same refresh rates when in boost mode.

      The sizes are also meant to be almost exactly the same at 0.50 inches X-T3 and 0.48 inches X-H1 with the same resolution.
      However the X-H1 EVF feels smaller (bigger black border around the edges) and not as clear. It also gives me eye strain after just a few minutes. (I have adjusted diopter). It feels like its further away if that makes sense?

      Has anyone else noticed a difference between the EVFs when using them side by side because on paper they are meant to be the same. Perhaps its just this particular X-H1.

      Thanks,
    • By Creativestubble
      Hi all,
       
      Just purchased an X-H1 (long time X-pro2 user) - seems a very nice camera. It seems the processor is a bit slower than my pro2. Software is 2.13.
      Question, is there any way around EVF blackout (besides at CH @ 11fps?) Its really distracting. My Pro2 does not do this at all.
      Thanks all,
      Darren
    • By Gibby
      I'm shooting video with X-T4 on a gimbal, in continuous mode with face detect on.  If I try to change the focus point using the rear touch screen (pressing top right corner of screen until it gets to "AF", and then click on the desired focus point on the screen...it will refocus on that area, but only once.  As if it was switched to single focus mode.  The manual however, seems to indicate that the camera should remain in continuous focus mode and track that subject, which it doesn't.   I would like be able to click on a point using the rear screen and have the camera track in continuous focus.  Is this even possible?  Not clear in the manual.  tks.
    • By Gibby
      For stills, I'm using backbutton focus.  And I'm able to select the focus point and track it in continuous focus.  Works great.  But in video mode, I can't find a way to track an object - only a face using face detect.  The rear touch screen doesn't seem to work this way.  When I select a point, it behaves as single focus, even when the camera is set to continuous focus.  Also, I'm often using the camera on a gimbal and need to rely on the rear screen for setting the focus point.  To date, I've mainly had to use the X-T4 in manual mode for video which is disappointing.  Am I missing something?
    • By R3D
      Hi All,

      Hope that some encountered that problem before and can help.
      I get my X-T4 a few weeks ago with FW 1.17 and it seemed to work correctly but just for the sake of having most up-to-date version I updated to 1.22). 
      After the update my fav view mode ([EYE SENSOR] + [LCD IMAGE DISP.]) is corrupted. It essentially keeps the LCD on whenever eye is away from EVF.
      Image preview is set 1.5 sec and is displayed correctly only on LCD screen. I set the LCD do info screen but it's not really how I'd like to have it working. 
      I was hoping that 1.23 will fix it but unfortunately no change after yesterday's release. 
      Thank you in advance! 
      R. 
       
  • Posts

×
×
  • Create New...