Jump to content

Why Does Fujifilm recommend against using a USB hub?

Steve533

By Steve533
in General Discussion

 Share

Recommended Posts

jerryy Veteran

jerryy

Posted
Posted (edited)

There is the issue of power, some hubs have a "brick" power supply and others are powered by the host port which will quickly drain a camera battery since the camera usb host port would be required to give each port on the hub enough power to meet the USB specs -- the camera battery does not stand a chance.

Also there is the bandwidth issue, each port on the hub is given data speeds that are a portion of the total the camera port can deliver. According to the USB specs, depending on the device you are trying to attach to the hub port, that portion may be even further restricted so that the main port is not overwhelmed trying to handle the possible data transfer requests. In a manner of speaking, you could starve a program you are trying to feed stills and / or video data to from the camera, if you pass the data through a hub instead of directly.

Edited by jerryy
Link to post
Share on other sites
Steve533 Apprentice

Steve533

Posted
  • Author
Posted
On 4/12/2021 at 7:19 PM, jlmphotos said:

IT's a "suggestion". Have you tried it?  If it doesn't work, it could be a power issue.

 

I haven’t even got the camera yet. I’m trying to understand as much as possible about the idiosyncratic things that aren’t obvious.

I’m hesitant to connect something Fujifilm recommends against. I thought it was electrical as well. Guess I’ll find out...

Link to post
Share on other sites
Steve533 Apprentice

Steve533

Posted
  • Author
Posted
On 4/12/2021 at 7:51 PM, jerryy said:

There is the issue of power, some hubs have a "brick" power supply and others are powered by the host port which will quickly drain a camera battery since the camera usb host port would be required to give each port on the hub enough power to meet the USB specs -- the camera battery does not stand a chance.

Also there is the bandwidth issue, each port on the hub is given data speeds that are a portion of the total the camera port can deliver. According to the USB specs, depending on the device you are trying to attach to the hub port, that portion may be even further restricted so that the main port is not overwhelmed trying to handle the possible data transfer requests. In a manner of speaking, you could starve a program you are trying to feed stills and / or video data to from the camera, if you pass the data through a hub instead of directly.

Thanks for the input Jerry.I’ll make sure of the bandwidth for the connection before disappointment.

BTW, have you used the Bluetooth/WiFi to transfer image files?

Link to post
Share on other sites
jerryy Veteran

jerryy

Posted
Posted
3 hours ago, Steve533 said:

Thanks for the input Jerry.I’ll make sure of the bandwidth for the connection before disappointment.

BTW, have you used the Bluetooth/WiFi to transfer image files?

i tried it to make sure the thing worked. For me, using a usb / thunderbolt card reader works better and is a lot faster at moving the image data over to the computer.

Link to post
Share on other sites
  • 1 month later...
VictorM Apprentice

VictorM

Posted
Posted (edited)
On 4/14/2021 at 10:35 PM, Steve533 said:

I haven’t even got the camera yet. I’m trying to understand as much as possible about the idiosyncratic things that aren’t obvious.

I’m hesitant to connect something Fujifilm recommends against. I thought it was electrical as well. Guess I’ll find out...

USB is USB. you don't need Fuji-approved cable. I use cable microUSB from my old mobile phone (which is a rarity now, more modern phones use USB-C connector)

Edited by VictorM
aaa
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Content

  • Posts

    • LBAbrams
      pocket wizard and XT5?

      By LBAbrams · Posted

      Has anyone successfully used pocket wizards with an XT5? I cannot get it to fire.  Do Fujis and pocket wizards get along? Thanks in advance for your wisdom on this, kind readers!
    • George_P
      Transfer X-T5 for PC wi fi...

      By George_P · Posted

      Grzegorz, Go to the Networking Setting in your camera menu (the last one at the bottom - unless you have a My Menu then that is the last one). There, go to Network Setting and choose the SSID (name) of your WiFi network, type in the password, choose "SET". If you have a functioning DHCP server on your network, the camera should get its IP address (and Subnet_Mask and Gateway). If not, you can enter these manually. It is a little tricky, there will be some zeros already here, move the cursor after the zero and use DEL to delete it and make space in the input fields for your own correct values. If you do not know what to enter, have a look at values in the network settings of your computer and use the same except for the IP address, try some fairly higher number, hopefully you hit an unused one. Usually the values would be something like IP: 192.168.1.188, Subnet Mask: 255.255.255.0, Gateway IP: 192.168.1.1  or something like that, take clues from your computer. The camera and computer must be on the same network. Then in Connection Mode on the camera, choose Wireless Tethering Fixed. And half-press the shutter to exit the menu and get in shooting mode. The red LED should be blinking. If you can look at your network devices, e.g. on your router, you should see the camera there. You can see check the camera settings in the camera menu in the INFORMATION item of the Network Setting menu to see the MAC address of your camera and look for it in the list of devices on your network.  Then use the tethering in your software, e.g. in Capture One. The camera may not show immediately, take a shot and then it should show in the list of available cameras. Good luck. Report back how did you fare.  PS If you have a Windows machine, you need to have Bonjour installed and running. Macs have it.
    • grizzski
      X-T30 II Eye Sensor + LCD Image Display viewmode not working

      By grizzski · Posted

      Hey all, I just got my first camera. The X-T30 II. It seems the Eye Sensor + LCD Image Display view-mode is doing the exact same thing as just the Eye Sensor view-mode setting. Any ideas why this is or what's supposed to be happening? Firmware Version: 2.04
    • George_P
      Problem with multi exposure on XT5

      By George_P · Posted

      What GordW said. You have to put the drive mode dial to "S" - Single Frame. If you have it on CL, CH, BKT or Panorama (or HDR), the Multiple Exposure option will be greyed out in the shootng menu. On my X-T5 it works in RAW + JPG and also in JPG only. When Multiple Exposure is switched on, the image quality cannot be set to RAW only. If it was set to RAW only before switching Multiple Exposure On, image quality defaults to RAW+Fine. The result is JPG. After each shot press MENU/OK and after the last one press DISP/BACK.  
    • N.Rio
      black and white (open thread)

      By N.Rio · Posted

      Springtime is coming to the Norwegian fjords.  X-E4 with XC 15-45

      Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

×
×
  • Create New...