Jump to content

Hello from Kansas City suburbs and Soligor question

Guest welshkc

By Guest welshkc
in Newbie / Self Introduction

 Share

Recommended Posts

Guest welshkc

Guest welshkc

Posted
Posted

I'm Ed in Lenexa, KS.

 

Amateur at its worst, but have been shooting since before digital.  Started with a Minolta Maxxum and went digital in 2006.

 

Just recently picked up a X-T1 to consider in place of my Nikon D3300.  Also keep a couple of film cameras around for fun.  Canon A1 and Canon EOS 630.

 

Here are a few my recent shots.  There are a few in there shot with Velvia slide film.  

 

https://www.flickr.com/photos/welshkc

 

 

If this is the right spot, I also have a question about the X-T1 and a Soligor 650mm lens I was recently given.

 

An adapter is working just fine for attaching the Soligor to the X body.  It is a t-mount system and the adapter was easy to find.  The Soligor is 650mm with a fixed F/8.5 aperture.  I found in the menu where to set the lens length for inclusion in the metadata, but the aperture setting menu item is grayed out.

 

Since the camera has no way to know what the aperture is, it actually reads F/0, then it would have problems with calculating the exposure.  Right?

 

Of course I am running in all manual mode, but would like to use Av if possible.  The X-T1 manual didn't have any clues.

 

Can anyone point me the right direction for why the aperture setting menu item is not available with this adapted lens?

 

Thanks and I am glad to have found a X system community.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Content

  • Posts

    • LBAbrams
      pocket wizard and XT5?

      By LBAbrams · Posted

      Has anyone successfully used pocket wizards with an XT5? I cannot get it to fire.  Do Fujis and pocket wizards get along? Thanks in advance for your wisdom on this, kind readers!
    • George_P
      Transfer X-T5 for PC wi fi...

      By George_P · Posted

      Grzegorz, Go to the Networking Setting in your camera menu (the last one at the bottom - unless you have a My Menu then that is the last one). There, go to Network Setting and choose the SSID (name) of your WiFi network, type in the password, choose "SET". If you have a functioning DHCP server on your network, the camera should get its IP address (and Subnet_Mask and Gateway). If not, you can enter these manually. It is a little tricky, there will be some zeros already here, move the cursor after the zero and use DEL to delete it and make space in the input fields for your own correct values. If you do not know what to enter, have a look at values in the network settings of your computer and use the same except for the IP address, try some fairly higher number, hopefully you hit an unused one. Usually the values would be something like IP: 192.168.1.188, Subnet Mask: 255.255.255.0, Gateway IP: 192.168.1.1  or something like that, take clues from your computer. The camera and computer must be on the same network. Then in Connection Mode on the camera, choose Wireless Tethering Fixed. And half-press the shutter to exit the menu and get in shooting mode. The red LED should be blinking. If you can look at your network devices, e.g. on your router, you should see the camera there. You can see check the camera settings in the camera menu in the INFORMATION item of the Network Setting menu to see the MAC address of your camera and look for it in the list of devices on your network.  Then use the tethering in your software, e.g. in Capture One. The camera may not show immediately, take a shot and then it should show in the list of available cameras. Good luck. Report back how did you fare.  PS If you have a Windows machine, you need to have Bonjour installed and running. Macs have it.
    • grizzski
      X-T30 II Eye Sensor + LCD Image Display viewmode not working

      By grizzski · Posted

      Hey all, I just got my first camera. The X-T30 II. It seems the Eye Sensor + LCD Image Display view-mode is doing the exact same thing as just the Eye Sensor view-mode setting. Any ideas why this is or what's supposed to be happening? Firmware Version: 2.04
    • George_P
      Problem with multi exposure on XT5

      By George_P · Posted

      What GordW said. You have to put the drive mode dial to "S" - Single Frame. If you have it on CL, CH, BKT or Panorama (or HDR), the Multiple Exposure option will be greyed out in the shootng menu. On my X-T5 it works in RAW + JPG and also in JPG only. When Multiple Exposure is switched on, the image quality cannot be set to RAW only. If it was set to RAW only before switching Multiple Exposure On, image quality defaults to RAW+Fine. The result is JPG. After each shot press MENU/OK and after the last one press DISP/BACK.  
    • N.Rio
      black and white (open thread)

      By N.Rio · Posted

      Springtime is coming to the Norwegian fjords.  X-E4 with XC 15-45

      Welcome, dear visitor! As registered member you'd see an image here…

      Simply register for free here – We are always happy to welcome new members!

×
×
  • Create New...